|
Single-Turn
Wire-Wound Potentiometer |
Series
- RP19, RP20 |
|
|
|
|
 Download
|
|
|
| High
Precision Range |
| |
| Bushing
Mount |
| |
| Economical |
|
|
|
|
|
|
-
7/8"
(22mm) Diameter
|
|
- 1
Million Turns Life
|
|
- High
Resolution
|
|
- 100
to 20K ohms Resistance Values
|
|
|
|
Industry
standard 22mm (7/8") body diameter with side terminals. Long life, high precision with a wide range of options available.
Available with or without mechanical end stops.
|
|
|
|
Electrical
Specifications |
RP19
|
RP20
|
|
Electrical
Angle |
320 ±5º
|
355 +3,-5º
|
|
Resistance
Value (S) |
100 ~ 20k
|
|
Resistance
Tolerance |
|
|
Linearity
Tolerance (std.) |
±0.5% |
|
Linearity
Tolerance (best) |
±0.25% > 2k ohm |
|
End
Resistance |
<1k: 0.2%
>=1k: 0.1% |
|
Wiper Current |
30
mA nominal |
|
Power @ 40º
(W) |
1.5 |
|
Insulation Resistance
|
>1000
Mohm @ 1000 VDC |
|
Dielectric Strength
|
1 minute @
1000 VAC |
|
Noise
|
<
100 ohms
ENR |
|
Mechanical
Specifications |
|
Mechanical
Angle |
320º ±5º
|
360º (continuous)
|
|
Maximum
Operating Torque |
0.3
(Ncm) |
|
Stopper
Strength |
25
(Ncm) |
- |
|
Life
Expectancy |
1
million cycles |
|
Max. Axial
Play of Shaft |
0.2
mm |
|
Max. Radial
Play of Shaft |
0.1
mm |
|
Vibration |
15
g / 10Hz to 2,000 Hz |
|
Shock |
50
g / 11ms |
|
Bearing |
Sleeve
bearing |
|
Environmental
Specifications |
|
Operating
Temperature |
-40ºC to
+105ºC |
|
IP Protection
Grade |
IP40
(IP65 optional) |
|
Standard |
per
MIL-R-12934 |
|
Materials |
|
Housing |
Engineered plastic
(glass reinforced, Polyamid) |
|
Shaft |
Stainless steel |
|
Bushing |
Brass |
|
Terminals |
Gold plated -solderable
or snap-on (DIN 46247) |
|
Resolution
Chart |
| Resistance
Value (ohms) |
Resolution
(%) |
Vmax
across element (V) |
Imax
through element (mA) |
Temperature
coefficient of element (±ppm/k) |
|
100 |
0.270 |
12 |
120 |
80 |
|
200 |
0.210 |
17 |
87 |
|
500 |
0.220 |
27 |
55 |
20 |
|
1k |
0.180 |
39 |
40 |
|
2k |
0.140 |
55 |
27 |
|
5k |
0.100 |
86 |
17 |
|
10k |
0.084 |
120 |
12 |
|
20k |
0.067 |
170 |
8 |
|
|
Standard
Dimesnisons (mm) |
|
|
|
Options |
|
-
Extra tap (1 only) |
-
Special operating angles |
-
Higher IP ratings |
|
-
Special shaft machining |
-
Tighter tolerances |
-
Special resistance values |
|
-
Rear shaft
|
-
Multiple gangs (up to 10) |
-
High torque |
|
-
Slipping clutch
|
-
Sealed housing |
-
O-ring shaft seal |
|
| |
|
| P3
America, Inc. |
| 3089C
Clairemont Dr. #363 - San Diego, Ca. 92117 |
| Phone:(858)
277-1420 Fax: (858) 225-0439 |
| www.p3america.com |
|
|
©
P3 America, Inc. 2004 - 2006. All Rights Reserved |
|
|
